![]() ![]() Then set up SSD caching again on the previous cache space. ![]() Then when you do that reinstall on the SSD in the unused space. You will have to install on the HDD and set up the cache for xxGB of the SSD (up to 64GB). Setting up the SSD as the OS drive and the cache drive. Follow the instructions in the above guide, only instead of using your OS SSD as the cache SSD use the one you designated for caching the HDD.Once that is set, install on your caching SSD.The system should already have windows installed on the main SSD and the SATA mode should be set to RAID, if you need to change your sata mode look here: ( link).Option 2: Set up caching on a secondary drive with a separate, non-OS SSD for caching After clicking OK button, SRT will enable automatically, and the RST GUI will refresh to show the newly accelerated system configuration.Click Enable acceleration either under the Status or Accelerate menu.Run the Intel RST software through the All Programs menu or the task bar icon.Have both the HDD you intend to accelerate and the SSD in system at this point.Install the newest Intel Rapid Storage Technology driver with the Control Center (a check box in the bottom left corner when installing): ( link).If you have the OS installed and the SATA mode currently set to IDE or AHCI please look here on how to properly change to RAID mode: ( link) Install Windows onto the HDD with the SATA mode set to RAID in the BIOS/UEFI.Operating system: Microsoft Windows* Vista 32-bit Edition and 64-bit Edition, Microsoft Windows* 7 32-bit Edition and 64-bit.Solid State Drive (SSD) with a minimum capacity of 18.6GB.Single hard disk drive or multiple drives in a single RAID volume.Intel Rapid Storage Technology software 10.5 version release or later.Intel® Core™ Processor in the LGA 1155 package.Intel® Z68/Z77/H77/Q77 Express Chipset-based desktop board.So, go to disk management and delete all the partitions on the SSD or use the diskpart clean command to delete the partitions that way before you begin. And you can only have one volume accelerated at a time.Īlso, before you try to set it up make sure your SSD has no partitions on it. ![]() Just remember all data on the SSD you use will be wiped when you accelerate the other drives. You can use a SSD to cache your secondary drives and RAID arrays. Intel® Smart Response Technology caching is implemented as a single drive letter solution no additional drive letter is required for the SSD device used as cache. This provides the advantage of having a hard disk drive (or a RAID volume) for maximum storage capacity while delivering an SSD-like overall system performance experience. ![]() It allows a user to configure computer systems with an SSD used as cache memory between the hard disk drive and system memory. Intel® Smart Response Technology is an Intel® Rapid Storage Technology (RST) caching feature that improves computer system performance. This feature requires that the SATA controller be set to RAID mode via the system BIOS. Intel® Smart Response Technology User Guide: So I decided to reboot.and voilà: RAID is not recognized anymore, system doesn't boot at all with none of the HDs.How to: Set up Intel Smart Response Technology (SSD caching) So I tried anyway to rebuild with "sudo dmraid -R " to get rid of the "rebuild" flag.Īfter I've done this, 1 HD wasn't recognized anymore from Ubuntu. Told me the RAID had 2 HD with the same blocks.įrom here everything seemed working properly. I followed these steps, from the last messages:Ĭonfigure mdadm for existing intel rapid storage array Also the boot time was incredibly longer than usual. I enter the utility and it tells me I need to rebuild the RAID from the operating system. So I shut down and replug correctly the HD.Īt the reboot, the RAID boot screen flags RAID with "REBUILD". Everything was running flawlessly, but the day after I've realized that 1 HD was disconnected. Only Ubuntu Desktop version recognized the Intel RAID configuration (I don't know why the server version didn't).Īnyway, while mounting back again everything after the first setup, unluckily a cable didn't get connected properly. I did use the Intel RST built in functionality. I have set up a local server with an old laptop so I was using RAID 1 mirroring for reliability= 2* 1TB HD SATA 2.5". ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |